SEE Computer Science Unit 1: Computer Network and Communication - Notes and Exam Questions
Unit 1 of Grade 10 Computer Science, Computer Network and Communication, deals with the way computers, phones and other devices are joined so that they can share files, printers and an Internet connection. It covers the key terms of telecommunication (broadband, bandwidth, throughput, data packet, frequency), wired and wireless media, connectors, networking devices, topologies, networks by coverage, network architecture and protocols, IP addressing, the internet, intranet and extranet, and the four network commands of the practical, and it carries 11 marks out of 50 in the SEE specification grid.
Unit at a glance
| Item | Details |
|---|---|
| Marks in SEE | 11 marks out of 50 in the official CDC specification grid for the new course: 3 multiple-choice questions (1 mark each) + 2 short questions (2 marks each) + 1 long question (4 marks). Only Python (12 marks) carries more. |
| Position in the paper | In the CDC model paper (2083), Unit 1 comes first in every group: the first three MCQs, the first two short questions of Group B and the first long question of Group C. |
| 1-mark questions (Group A) | One term identified from its description (for example bandwidth), one "why is this medium or technology suitable" question, and one "which command or device is used" situation. |
| 2-mark questions (Group B) | "Differentiate between two terms" (two points, 1 mark each) and "name the technology in this situation and explain how it works" (1 + 1). |
| 4-mark question (Group C) | Types with features and uses, with a split such as [1+3] or [2+2]; the model paper's long question was on types of broadband connection, split [1+3]. |
| Topics seen in the papers reviewed | The CDC model paper 2083 and the SEE 2081 and 2082 papers (old course) were studied. Each of these came up at least once: telecommunication, modes (simplex), transmission media, guided vs unguided media, LAN, client-server vs peer-to-peer, internet vs intranet, bandwidth, wireless technology, network commands, types of broadband connection. SEE 2083 is the first examination on this new course, so the list shows a pattern, not a promise; the whole unit should be studied. |
| Recommended preparation | The definitions of the key terms, the five devices, the four topologies with one advantage and one disadvantage each, PAN/LAN/MAN/WAN with examples, the IPv4 vs IPv6 table, internet/intranet/extranet, and the uses of ping, ipconfig, tracert and nslookup. In a "differentiate" answer, both sides of each point are written (for example "a hub sends to all other ports, while a switch sends only to the destination port"). |
1.1 Concept of telecommunication and key terminology
This topic covers the meaning of telecommunication, the parts of a communication system, and the key terms broadband, bandwidth, throughput, 3G/4G/5G, data packet and frequency, together with the modes of communication.
Telecommunication
(What is telecommunication? Define telecommunication with examples.)
Telecommunication is the sending and receiving of messages, sound or pictures across a long distance by electrical, radio or light signals that electronic devices produce and receive. Telephones, mobile phones, radio, television and computers all take part in it. Examples: a phone call, an SMS, a TV programme and an online class.
In a phone call, for instance, the voice of the caller is changed into electrical signals, then into radio waves that travel to a mobile tower, through the operator's network, and back into sound at the other phone. The word joins the Greek tele, meaning far, with the Latin communicare, meaning to share.
(What are the basic components of a communication system?)
A data communication system is usually described as having five basic parts:
- Sender: the device that sends the message.
- Receiver: the device that receives it.
- Message: the data being sent.
- Medium: the path that carries it (cable or air).
- Protocol: the rules both sides follow.
Broadband
(What is broadband? What are the types of broadband connection?)
Broadband is a fast Internet connection that stays on all the time and can carry many kinds of data (video, voice, files) at once. It replaced slow dial-up Internet, which used the phone line, was very slow, and did not allow a phone call while the line was online. With broadband, a class can be streamed, notes downloaded and a video call made at the same time. The connection is supplied by an ISP (Internet Service Provider), the company that connects homes, schools and offices to the Internet.
| Type of broadband | How it carries data | Advantage | Limitation | Suitable for |
|---|---|---|---|---|
| DSL (Digital Subscriber Line) | Through the copper telephone line | Uses lines that already exist | Speed falls as distance from the telephone exchange grows | Homes near an exchange |
| Cable | Through the coaxial cable used for cable TV | Usually faster than DSL; TV and Internet on one cable | Speed drops at busy times because neighbours share the line | Towns with cable TV networks |
| Fibre optic (FTTH) | As light through thin glass fibres | Very high speed, little loss, not disturbed by electrical noise | The cable must reach the building; costly to lay | Cities, offices, schools on a fibre route |
| Satellite | By radio signals to and from a satellite | Works almost anywhere, even remote hills | Expensive; noticeable delay; heavy rain can weaken signal | Remote areas with no cable |
| Wireless (4G/5G, fixed wireless, Wi-Fi hotspots) | By radio waves from towers or access points | No cable needed to each user; quick to set up; mobile data can be used on the move | Speed depends on signal strength and number of users | Places with good mobile coverage |
Bandwidth and throughput
(What is bandwidth? What is throughput?)
Bandwidth is the maximum rate at which a link can carry data, that is, the largest number of bits it can carry each second (its capacity). Unit: bits per second (bps, kbps, Mbps, Gbps).
Throughput is the amount of data that actually reaches the other end per second. It is measured in the same units as bandwidth and cannot be higher than the bandwidth of that same link.
A related term is latency: the delay between sending data and its arrival, usually given in milliseconds (ms).
(Why is the throughput of a link usually lower than its bandwidth?)
Throughput is usually lower because bandwidth is only the upper limit of the link, while the data that actually arrives is reduced by sharing, interference and losses on the way. Bandwidth may be compared with the width of a water pipe, the most water (data) it could carry each second, and throughput with the water that actually comes out of the tap each second. If many houses use the same pipe, or some water is lost on the way, less water arrives, although the pipe is just as wide. In a network, other users sharing the line, interference and weak signals have the same effect. Typical causes of lower throughput:
- many users sharing the line at the same time (congestion);
- a weak Wi-Fi signal, walls or interference;
- a long distance, a busy server or an old device.
Figure 1: Bandwidth is how much the link could carry; throughput is how much actually gets through.
(Differentiate between bandwidth and throughput.)
| Bandwidth | Throughput |
|---|---|
| The most data a link is able to carry each second (its capacity). | The data that actually reaches the far end in each second. |
| A set maximum for that link or plan that does not change from minute to minute, for example a 100 Mbps plan. | Changes from moment to moment with congestion, signal strength, distance and devices; it cannot exceed the bandwidth of the same link. |
(How is the time to download a file found from the throughput? Why is a file size in MB multiplied by 8?)
Both bandwidth and throughput are measured in bits per second. A small b stands for bits and a capital B for bytes; 1 byte = 8 bits. Internet plans are sold in megabits per second (Mbps), but file sizes are shown in megabytes (MB). For this reason a size in MB is multiplied by 8 to obtain megabits (Mb) before it is divided by the speed. Writing Mbps and MB as the same unit is a common error.
\[ \text{throughput} = \frac{\text{data actually transferred (bits)}}{\text{time taken (seconds)}} \qquad \text{time} = \frac{\text{file size in bits}}{\text{throughput}} \](Worked example 1. A 240 MB video lecture downloads at a steady throughput of 16 Mbps. How long does the download take?)
Given: file size = 240 MB; throughput = 16 Mbps.
To find: time taken.
Formula: time = file size in bits ÷ throughput.
Solution: file size in megabits \( = 240 \times 8 = 1920 \) Mb. Time \( = \dfrac{1920\ \text{Mb}}{16\ \text{Mbps}} = 120\ \text{s} = 2 \) minutes.
Answer: 120 s, that is, 2 minutes.
Conditions: 1 MB is taken as 8 Mb (both in decimal units: 1 MB = 1,000,000 bytes and 1 Mb = 1,000,000 bits, as ISPs count), and the throughput is assumed to stay the same for the whole download. In practice it rises and falls, so the time is an estimate.
(Worked example 2. A school buys a 100 Mbps plan, but a speed test shows 45 Mbps. Identify the bandwidth and the throughput, and find what percentage of the capacity is obtained.)
Given: plan speed = 100 Mbps; speed-test result = 45 Mbps.
To find: the bandwidth, the throughput, and the percentage of the capacity obtained.
Formula: percentage of capacity = (throughput ÷ bandwidth) × 100%.
Solution: The plan states the most the link can carry, so the bandwidth is 100 Mbps; the speed test measures the data that actually arrives, so the throughput is 45 Mbps. Percentage \( = \dfrac{45\ \text{Mbps}}{100\ \text{Mbps}} \times 100\% = 45\% \).
Answer: bandwidth = 100 Mbps; throughput = 45 Mbps; the link is giving 45% of its capacity. Possible reasons: many students online at once, a weak Wi-Fi signal in that room, or a busy server.
3G, 4G and 5G
(What do 3G, 4G and 5G mean? Write the main features of each generation.)
"G" stands for generation. Each new generation of mobile network carries more data, with less delay, to more phones at the same time.
| Generation | What it made possible | Everyday use |
|---|---|---|
| 3G | Internet on phones at a usable speed; convenient picture and video messaging; video calls on phones became practical | Browsing, email, social media on a phone |
| 4G (LTE = Long Term Evolution) | Fast enough for HD streaming, with short delay in both downloading and uploading | HD video streaming, online classes, video calls, online games, cloud apps |
| 5G | Very high speed, very low delay, and a huge number of devices connected in one area | Smart cities and IoT (Internet of Things) sensors, self-driving vehicle trials, AR/VR (augmented and virtual reality), remote surgery trials, crowded places like stadiums |
Data packets
(What is a data packet?)
A data packet is a small piece of a message that carries part of the data together with a header that holds the addresses of the sender and the receiver. A large file is not sent in one piece; it is cut into small packets. Each packet has a header (where it came from, where it is going, and its number in the sequence) and a small piece of the data (the payload). Some books also show a trailer at the end that holds error-checking bits.
(How do data packets travel from the sender to the receiver?)
Each router reads the destination IP address and, using its routing table, passes the packet on to the next router on the best path it knows. Routes can change while a file is being sent, so packets of the same file may take different routes; the receiving computer puts them back in order using their numbers.
Figure 2: A file split into packets that travel by different routes and are rejoined in order.
(Why is a message sent as many data packets instead of one block?)
- Many users can share the same line, because packets from different people take turns.
- If a packet is lost or damaged, TCP (the set of rules that checks delivery) notices the gap and has the missing data sent again, so the whole file does not need to be sent again.
- If a link breaks, routers can send later packets another way.
Frequency
(What is frequency? In which unit is it measured?)
Frequency is the number of full wave cycles that pass a point in each second. Wireless signals are waves, and the frequency of a signal states how many full waves pass every second. Unit: hertz (Hz); 1 kHz = 1,000 Hz, 1 MHz = 1,000,000 Hz, 1 GHz = 1,000,000,000 Hz. Different services are given different frequency bands so that they do not disturb each other.
| Service | Typical frequency |
|---|---|
| FM radio | 88 to 108 MHz |
| GPS (main civilian signal) | 1575.42 MHz |
| Wi-Fi | 2.4 GHz and 5 GHz bands (newer routers also use 6 GHz) |
| Bluetooth | 2.4 GHz band |
| Microwave oven (not communication, but it shares the band) | about 2.45 GHz |
On Wi-Fi, the 2.4 GHz band reaches farther and passes walls better, while the 5 GHz band is usually faster but covers a shorter distance.
(Worked example 3. Express 2.4 GHz in MHz and in Hz.)
Given: frequency = 2.4 GHz.
To find: the frequency in MHz and in Hz.
Formula: 1 GHz = 1000 MHz = \( 10^{9} \) Hz.
Solution: In MHz: 2.4 × 1000 = 2400 MHz. In Hz: 2.4 × \( 10^{9} \) Hz = 2,400,000,000 Hz.
Answer: 2.4 GHz = 2400 MHz = \( 2.4 \times 10^{9} \) Hz. The wave therefore repeats 2.4 billion times every second.
Modes of communication
(What is a mode of communication? Explain simplex, half duplex and full duplex mode with examples.)
Data communication is the movement of data from one computer or device to another through some medium. The mode of communication states in which direction data can flow between two devices.
- Simplex: data flows in one direction only. The receiver can never reply on the same channel. Examples: FM radio and TV broadcasts, where listeners and viewers only receive. (Some guides give "keyboard to computer" as an example; it is avoided here, because a modern keyboard also receives small signals from the computer, for example to switch on its Caps Lock light.)
- Half duplex: data can flow both ways, but only one way at a time; the two sides take turns. Example: a walkie-talkie, where the button is pressed to talk and released to listen.
- Full duplex: data flows both ways at the same time. Examples: a phone call or video call, where both people can talk and hear together.
Figure 3: Simplex, half duplex and full duplex.
1.2 Communication media: wired and wireless
(What is communication media? What is transmission media? What are its types?)
Communication media is the path that carries signals between devices. It is also called transmission media, because the signal is transmitted along it. There are two families: guided (wired) media, which use cables, and unguided (wireless) media, which use air or space.
Guided (wired) media
(What is guided media? Explain twisted-pair cable, coaxial cable and optical fibre.)
Guided media keep the signal inside a physical cable, so the signal follows a fixed path.
- Twisted-pair cable (CAT6): eight thin copper wires twisted into four pairs. The twisting cancels out much of the electrical noise from nearby wires. On a cable run of 100 m or less CAT6 handles 1 Gbps, and on a much shorter run (about 55 m) it can reach 10 Gbps. It ends in an RJ45 plug and is the usual cable in school labs and offices. The older CAT5e looks similar but is rated for lower performance and suffers more crosstalk (interference between its own wire pairs).
- Coaxial cable: one copper wire in the centre, surrounded by insulation, a metal shield and an outer cover. It is used for cable TV and cable Internet.
- Optical fibre: a hair-thin strand of glass (or plastic) through which data travels as short flashes of light. The glass core is wrapped in cladding that bounces the light back inside, so the light can travel many kilometres with very little loss. Fibre is very fast, its light signal is not affected by electrical noise (glass does not carry electric current), and it is hard to tap secretly. It costs more and needs skilled workers to join. ISPs use it for their main lines and for FTTH (fibre to the home).
Unguided (wireless) media
(What is unguided media? Give examples.)
Unguided media send signals through air or space as radio waves, microwaves or infrared light. There is no cable, so devices can move about, but the signal can be weakened by walls, distance, weather and other signals. Examples: Wi-Fi, Bluetooth, RFID, microwave, satellite and infrared links.
(What is Wi-Fi? How does a laptop connect to the Internet through Wi-Fi?)
Wi-Fi (Wireless Fidelity, the full form given in the textbook; officially Wi-Fi is a brand name) connects phones, laptops and tablets to a network without cables over radio waves, in the 2.4 GHz and 5 GHz bands. The signals are sent and received by a wireless router or an access point. The laptop's wireless adapter exchanges these radio signals with the router or access point, and the router is joined to the ISP's line, so data passes between the laptop and the Internet with no cable to the laptop. Newer Wi-Fi can join two channels together for more speed (channel bonding) and aim the signal towards a device (beamforming). Range indoors is roughly a few tens of metres.
(What is Bluetooth? Why is Bluetooth suitable for connecting nearby devices?)
Bluetooth is a short-range, low-power radio link (typically about 10 m for phones and earbuds; the range varies with the device) for earbuds, speakers, smartwatches, keyboards and file sharing between phones. It suits nearby devices because no cable is needed, it uses little power, and its short range is enough for devices around one person. It keeps jumping between many channels many times a second (frequency hopping), which reduces interference.
(What is RFID? What are passive and active tags?)
RFID (Radio Frequency Identification) identifies objects by radio: a reader sends radio waves and a small tag answers with the number stored in it, without touching. Passive tags have no battery and work only close to the reader; active tags have a battery and can be read from farther away. Uses: library books, ID cards for gates, stock in warehouses, toll and parking tags, contactless payment cards.
(What is satellite communication? What are uplink and downlink?)
Satellite communication is communication in which signals are relayed through a satellite in space. In the basic relay model, a ground station sends a signal up to a communication satellite (the uplink); the satellite strengthens it and sends it down to a wide area (the downlink). Up to the satellite is the uplink and down to Earth is the downlink; the two are not to be interchanged. Uses: TV (direct-to-home dishes), weather forecasting, GPS navigation, Internet for remote places, and phones during disasters when ground networks fail. GPS works a little differently: GPS satellites only broadcast time and position signals, and a phone simply listens to several of them to work out its position; the phone sends nothing up.
Figure 4: Uplink goes up to the satellite; downlink comes down from it.
(Give reason: A video call through a geostationary satellite feels slightly late.)
A geostationary satellite is about 35,800 km above the equator. Radio waves travel at about 300,000 km per second, so one trip up and down again (about 71,600 km) takes at least \( \dfrac{71\,600}{300\,000} \approx 0.24 \) s. A reply must make the same trip back, so a question and its answer take at least about \( 2 \times 0.24 \approx 0.48 \) s, before any other delays are added. Newer low-orbit satellites fly much lower and have less delay.
Guided and unguided media compared
(Differentiate between guided and unguided media.)
| Point | Guided (wired) | Unguided (wireless) |
|---|---|---|
| Path of the signal | Inside a cable, along a fixed path | Through air or space, spreading out in many directions |
| Examples | Twisted pair (CAT6), coaxial, optical fibre | Wi-Fi, Bluetooth, RFID, microwave, satellite, infrared |
| Effect of weather and obstacles | Hardly affected | Rain, walls and distance can weaken the signal |
| Security | Harder to tap; a person needs to reach the cable | Signal can be picked up nearby, so passwords and encryption are needed |
| Movement | Device stays where the cable reaches | Device can move around (mobility) |
| Setting up | Cables must be laid, which is slow and costly over long distances | No cables; quick to set up; useful across rivers, hills or for whole regions (satellite) |
Guided media are not limited to short distances: optical fibre is guided media and carries data across countries and under oceans.
(Worked example 4. A college wants to link two buildings 400 m apart. Which medium is suitable? Give reasons.)
CAT6 is reliable only up to 100 m, so it is not suitable alone. Optical fibre carries light over many kilometres with little loss and is not disturbed by electrical noise, so fibre is the best choice, with a media converter (or a switch with a fibre port) at each end. If laying a cable is not possible (for example across a busy road), a point-to-point wireless link could be used instead.
1.3 Connector: RJ45 and media converter
(What is a connector? What is RJ45?)
A connector is the plug or fitting at the end of a cable that joins it to a device.
RJ45 (Registered Jack 45) is the clear plastic plug with 8 pins on the end of a twisted-pair (Ethernet) cable. It clicks into the network port of a computer, switch or router. It looks like a telephone plug but is wider: the phone plug (RJ11) is narrower, with 6 positions and usually only 2 or 4 metal contacts.
(Name the connectors used with optical fibre.)
Fibre cables use their own push-in or twist-on connectors, such as SC (square, push-pull), LC (small, used where many ports sit close together) and ST (round, bayonet twist-lock).
(What is a media converter? When is it used?)
A media converter is a small powered device that changes electrical signals from a copper cable into light for a fibre cable, and back again. Strictly it is a device rather than a plug, but it is studied with connectors because it joins copper cable to fibre. Typical reasons to use one:
- the copper run cannot stretch far enough;
- the link needs the greater speed and range of fibre.
Figure 5: RJ45 plug, the layers of an optical fibre, and media converters joining two buildings.
1.4 Networking devices: repeater, hub, switch, bridge and router
(What are the components of a computer network?)
A network is made of hardware (computers, the network interface card (NIC) through which each computer joins the network, cables, and devices such as switches and routers), software (the network operating system and programs) and the media that carries the signals.
(What is a networking device? Explain the functions of repeater, hub, switch, bridge and router.)
A networking device is hardware that connects computers and other nodes and passes data between them. The five devices of the syllabus are compared below.
| Device | Function | How it handles data | Typical place |
|---|---|---|---|
| Repeater | Receives a weak signal, rebuilds it to full strength and sends it on, so the network can reach farther. | Works on the signal only: it regenerates (boosts) signals; it does not read addresses. | Long cable runs; Wi-Fi extenders for an upstairs room. |
| Hub | A box with many ports. Whatever arrives on one port is copied out to every other port. | Does not read addresses: every computer receives every message, so the bandwidth is shared and collisions happen. | Old small networks; now mostly replaced by switches. |
| Switch | A box with many ports that builds a table of which device sits behind which port (using MAC addresses) and delivers each message only to the port of the device it is meant for. A message for everyone, or for a device it has not learned yet, goes out of all its other ports. | Reads MAC addresses and works within one network: less traffic, faster and more private than a hub. | The centre of a star network in labs and offices. |
| Bridge | Joins two parts (segments) of the same kind of network and passes on only the traffic that needs to cross. | Reads MAC addresses to decide to forward or block. | Splitting a busy LAN into two parts; joining two nearby LANs. |
| Router | Joins different networks (for example the school LAN and the ISP) and chooses the best path for each packet using IP addresses. | The most capable of the five: it reads IP addresses and keeps a routing table. | Between a home or school network and the Internet. |
(Give reason: A repeater extends a network but does not make it faster.)
A repeater only regenerates a weak signal so that it can travel farther; it does not raise the bandwidth of the link, so it adds reach, not speed.
(What are a modem and a wireless access point?)
A modem changes the computer's digital signals into the kind of signal the line carries (and back). A wireless access point is the unit that gives Wi-Fi devices a way into the cabled network. A home "Wi-Fi router" is usually a router, switch and access point in one box.
(Differentiate between a hub and a switch.)
| Hub | Switch |
|---|---|
| Copies every message that arrives out of all its other ports, so every computer receives it. | Sends each message only to the port of the destination device, using the table of MAC addresses it has learned. |
| The bandwidth is shared and collisions happen, so it is slower and less private. | Less traffic, so it is faster and more private. |
A hub does not send data to one computer only; that is the work of a switch.
Figure 6: A hub repeats data out of every other port; a switch delivers it to the destination port alone.
(Differentiate between a bridge and a router.)
| Bridge | Router |
|---|---|
| Joins two parts (segments) of the same kind of network. | Joins different networks, for example a LAN and the Internet. |
| Decides to forward or block traffic by reading MAC addresses. | Chooses the best path for each packet by reading IP addresses and its routing table. |
(Worked example 5. Name the device needed in each situation: (a) Wi-Fi does not reach the far end of a long hostel corridor; (b) forty computers in a lab must be connected to each other; (c) the lab must reach the Internet through the ISP; (d) a building's copper network must join a fibre line from the next building.)
(a) A repeater (Wi-Fi extender) placed where it still receives a good signal from the router (often about halfway along), or an extra access point cabled to the network there. (b) A switch. (c) A router. (d) A media converter.
1.5 Topology: bus, star, ring and hybrid
(What is network topology? What are physical and logical topology?)
Topology is the layout or pattern in which the devices (nodes) of a network are connected, such as bus, star, ring or hybrid. A node is any device connected to a network: a computer, printer, phone or switch. The physical topology is how the cables are laid; the logical topology is the path the data follows.
(Explain bus, star, ring and hybrid topology.)
Figure 7: Bus, star, ring and hybrid topologies.
- Bus: all devices are connected to one main cable called the backbone, with a terminator at each end to stop signals bouncing back. A message travels along the whole cable and every device sees it, but only the addressed device takes it.
- Star: every device has its own cable to a central switch (or hub). This is the most common layout in today's wired LANs.
- Ring: the devices sit in a circle, each linked to its two neighbours, so the cable has no loose end. Data is handed on from each device to its neighbour, in one direction, until the receiver is reached; every device refreshes the signal as it goes by.
- Hybrid: a network that combines two or more basic layouts. For example, each building of a campus may have its own star network, and the buildings are tied together by a ring of fibre cable. Large schools and offices use hybrid networks.
(Write the advantages and disadvantages of bus, star, ring and hybrid topology.)
| Topology | Advantages | Disadvantages |
|---|---|---|
| Bus | Needs the least cable; cheap and straightforward for a few computers; one more device is readily added to the backbone | A break in the backbone stops the whole network; slows down when many devices send; faults are hard to find |
| Star | One faulty cable or computer does not stop the others; devices are readily added, removed and checked for faults; fast with a switch | Needs more cable; if the central switch fails, the whole network stops |
| Ring | Every device gets an equal turn (for example by passing a "token" round the ring), so there are few collisions; works steadily under heavy traffic | One broken link or computer can stop the loop (unless a second ring is added); adding a device disturbs the network |
| Hybrid | Flexible: each part can use the best layout; grows without difficulty; a fault in one part usually stays there (but if the backbone joining the parts fails, the parts are cut off from each other) | More complex to design and manage; costs more |
(Which topology is used in most wired LANs today? Why?)
Star topology built around a switch. Older LANs used bus or ring, but star is preferred because one faulty cable or computer does not stop the others, devices are readily added or removed, and faults are quick to locate.
(Worked example 6. A cyber cafe has 15 computers and wants a network that can be repaired quickly when one cable fails. Which topology should it choose? Why?)
Star, with a 16-port or 24-port switch, because a broken cable affects only that one computer and the faulty cable is quick to find.
1.6 Overview of different networks based on coverage: PAN, LAN, MAN and WAN
(What is a computer network? What are its advantages?)
A computer network is two or more computers and other devices linked by cable or wireless signals so that they can exchange data and share resources such as printers, files and an Internet connection. A network allows users to:
- share hardware (printers, scanners, storage);
- share software and data;
- communicate (email, chat, video calls);
- keep central backups;
- share one Internet connection.
(What are the disadvantages of a computer network?)
- Buying the cables, devices and server, and keeping them running, costs money and needs a trained person.
- If a key part such as the server or the main switch fails, many users are stopped at once.
- Viruses and other malware can spread from one computer to others through the network, and an intruder who enters one computer may reach the others.
- Shared data can be read or stolen if passwords and permissions are weak.
(How are networks classified by coverage? Explain PAN, LAN, MAN and WAN with an example of each.)
Networks are sorted into types by the size of the area they serve.
Figure 8: Typical area covered by PAN, LAN, MAN and WAN, from the smallest to the largest.
| Type | Area | Example | Notes |
|---|---|---|---|
| PAN (Personal Area Network) | Around one person, usually within about 10 m | Phone with earbuds and a smartwatch over Bluetooth; phone tethered to a laptop by USB | Set up with very little effort; one owner |
| LAN (Local Area Network) | A room, building or campus (up to about 1 km) | A school computer lab; an office floor. A wireless LAN is called a WLAN. | Faster than MAN and WAN, few errors, usually owned by one organisation; most use star topology today (older LANs used bus or ring) |
| MAN (Metropolitan Area Network) | A city or valley | A cable TV/Internet network across a city; a company linking its offices around Kathmandu Valley | Joins many LANs; may be owned by one or several organisations |
| WAN (Wide Area Network) | A country, a continent or the whole world | The Internet (the largest WAN); a bank joining branches in many districts | Links are rented from telecom companies and satellite operators; slower and with more delay than a LAN; usually owned by many organisations |
(Differentiate between LAN and MAN.)
| LAN | MAN |
|---|---|
| Covers a small area such as a room, a building or a campus. | Covers a larger area such as a whole city or valley, often joining several LANs. |
| Usually owned and managed by one organisation, for example a school. | May be owned by one organisation or shared by several, for example a city-wide cable Internet network. |
| Higher data rate and fewer transmission errors, because the distances are short. | Lower data rate than a LAN (though higher than a WAN), because the links are longer. |
| Example: the network of a school computer lab. | Example: a company network joining its offices across Kathmandu Valley. |
1.7 Network architecture: client-server and peer-to-peer
(What is network architecture? What is a server and what is a client?)
Network architecture describes how the computers in a network are arranged to give and use services. A server is a computer (or program) that provides a service (files, login, web pages). A client is a computer (or program) that asks for and uses the service.
(Explain client-server and peer-to-peer architecture.)
- Client-server: a central computer called the server, usually more powerful than the rest, offers services such as file storage, logins, printing, email and websites. The other computers, the clients, ask for those services and use them. The server is managed centrally by an administrator. Server operating systems include Windows Server and Linux server editions (for example Ubuntu Server).
- Peer-to-peer (P2P): every computer has the same standing, so each is called a peer. Each one offers its own files or printer to the others and also uses what they offer. There is no dedicated server; this is also called a workgroup. Everyday systems like Windows 11, macOS and Linux include this kind of sharing.
Figure 9: Client-server and peer-to-peer architectures. The lines show who shares with whom, not the cables; in a real room the peers are usually cabled to one switch.
(Differentiate client-server architecture from peer-to-peer architecture.)
| Point | Client-server | Peer-to-peer |
|---|---|---|
| Server | Has a dedicated central server | No dedicated server; every computer is equal |
| Control and security | Central: one administrator manages users, passwords and permissions | Each user controls their own computer, so security is weaker |
| Backup | Central backup of all data on the server is possible | Each computer must be backed up separately |
| Cost | Costly: server hardware, server software and a trained administrator | Cheap and quick to set up |
| If a computer fails | If the server fails, every client loses its services; if one client fails, only that client is affected | Only that computer's shared files become unavailable; others keep working |
| Best for | Large networks: schools, banks, offices, websites | Small groups, about ten computers or fewer: a small office or home |
Network protocols
(What is a protocol? Write the full forms and functions of common network protocols.)
A protocol is the agreed set of rules for how data is arranged, sent and received, so that devices from different makers can understand one another, in the same way as two people need a shared language.
| Protocol | Full form | Function |
|---|---|---|
| TCP/IP | Transmission Control Protocol / Internet Protocol | The basic rules of the Internet: IP addresses and routes the packets, TCP checks that all packets arrive in the right order |
| HTTP | HyperText Transfer Protocol | Brings web pages from a web server to the browser |
| HTTPS | HyperText Transfer Protocol Secure | HTTP with encryption, so passwords and payments cannot readily be read on the way (the browser shows a security icon, often a padlock, next to the web address) |
| DHCP | Dynamic Host Configuration Protocol | Automatically gives an IP address (and settings such as the default gateway) to each device that asks for one when it joins the network |
| SMTP | Simple Mail Transfer Protocol | Sends email from a mail program to the mail server and between mail servers |
| FTP | File Transfer Protocol | Transfers files between computers, for example uploading a website's files to a server |
| DNS | Domain Name System | Turns a name such as example.com into its IP address |
| NCP | Network Control Protocol (also called Network Control Program) | The first host protocol of ARPANET, the early network that grew into the Internet; later replaced by TCP/IP |
1.8 Concept of IP addressing (IPv4 and IPv6)
(What is an IP address? Why does a device need one?)
An IP address is a number that identifies a device on a network so that data can be delivered to it, for example 192.168.1.15. Like a postal address for letters, it lets packets reach the right place, so every computer, phone or printer that sends and receives data on an IP network (such as the Internet) needs one. The Internet Protocol (IP) gives the address format and routes packets from network to network. Two versions are in use: IPv4 and IPv6.
(What is IPv4? Why have IPv4 addresses run short?)
IPv4 (version 4): each address is 32 bits long and is shown as four decimal numbers joined by full stops, for example 192.168.10.25. Each number is one octet (8 bits), so it can only be from 0 to 255; a number above 255 makes the address invalid. The total number of IPv4 addresses is \( 2^{32} = 4\,294\,967\,296 \) (about 4.3 billion). That is not enough for all the phones, computers and smart devices in the world, so IPv4 addresses have run short.
(What are private IP addresses and NAT?)
To save addresses, homes and schools use private addresses (such as 192.168.x.x, 10.x.x.x and 172.16.x.x to 172.31.x.x) inside, and the router shares one public address using NAT (Network Address Translation).
(What is IPv6? How is a long IPv6 address shortened?)
IPv6 (version 6): each address is 128 bits long (not 64 bits) and is shown in hexadecimal as eight blocks of four digits, with a colon between the blocks, for example 2001:0db8:0000:0000:0000:ff00:0042:8329. It gives \( 2^{128} \approx 3.4 \times 10^{38} \) addresses, enough for every device that can be imagined. A long IPv6 address can be shortened: leading zeros in a group may be dropped, and one run of all-zero groups may be replaced by :: (only once in an address).
Figure 10: The parts of an IPv4 and an IPv6 address.
(Differentiate between IPv4 and IPv6.)
| Point | IPv4 | IPv6 |
|---|---|---|
| Length | 32 bits | 128 bits |
| Written as | 4 decimal numbers (0 to 255) separated by dots | 8 groups of 4 hexadecimal digits separated by colons |
| Number of addresses | about \( 4.3 \times 10^{9} \) | about \( 3.4 \times 10^{38} \) |
| Setting the address | Typed by hand or given by DHCP | Can configure itself automatically, or use DHCP |
| Security | Encryption (IPsec) is an optional add-on | IPsec support was designed in from the start, but data is encrypted only when IPsec is actually switched on |
| Header size | 20 to 60 bytes (varies) | Fixed 40-byte main header (extra headers may follow) |
| Example | 192.168.1.15 | 2001:db8::15 |
(Worked example 7. State whether each address is valid: 192.168.1.300, 10.20.30, 172.16.40.7, 2001:db8::5 and 2001::db8::5.)
- 192.168.1.300: invalid, because 300 is more than 255.
- 10.20.30: invalid, because IPv4 needs four numbers.
- 172.16.40.7: valid IPv4 (and a private address).
- 2001:db8::5: valid, but it is IPv6, not IPv4.
- 2001::db8::5: invalid IPv6, because :: is used twice.
1.9 Concept of the internet, intranet and extranet
(What is the internet? What is an intranet? What is an extranet?)
- Internet: the worldwide, public network of networks. Anyone with a connection can use it. It runs on TCP/IP and offers services such as the web, email, file transfer (FTP), live text chat through IRC (Internet Relay Chat), Telnet (logging in to and working on a distant computer), video streaming, online shopping and social media.
- Intranet: a private network that uses the same technology as the Internet (TCP/IP, web pages, browsers) but only members of one organisation can enter, usually by logging in. Example: a school portal where teachers record attendance and students read notices.
- Extranet: part of an organisation's private network that is opened, with a login, to chosen outsiders such as suppliers, partners or customers. Example: parents log in to see only their own child's results; a book supplier logs in to see the school's orders.
Figure 11: Who is allowed into the internet, an extranet and an intranet. The circles show who has access, not how the cables are joined.
(Compare the internet, an intranet and an extranet.)
| Point | Internet | Intranet | Extranet |
|---|---|---|---|
| Who can use it | Everyone (public) | Only members of the organisation | Members plus chosen outsiders with permission |
| Size | Worldwide | Inside one organisation | One organisation and its partners |
| Main purpose | Link people worldwide and make information available to all | Let staff communicate and use shared resources internally | Give partners or customers access to selected information only |
| Security | Least controlled; users need firewalls and antivirus | Most restricted access (members only), though it still needs passwords, permissions and updates | Private, yet outsiders must be let in carefully, with logins and limits |
| Example | Public websites, search engines, video sites | Company or school staff portal | Supplier or client portal; parents' result portal |
(Differentiate between internet and intranet.)
| Internet | Intranet |
|---|---|
| Public: anyone with a connection can use it. | Private: only members of one organisation can enter, usually by logging in. |
| Worldwide network of networks that makes information available to all. | Works inside one organisation, so that staff can communicate and use shared resources. |
| Least controlled; users need firewalls and antivirus. | More private and closely controlled; outsiders are not given access. |
(Give reason: An intranet uses Internet technology, yet it is not open to the public.)
An intranet runs on the same TCP/IP, web pages and browsers as the Internet; "intranet" does not mean a network without Internet technology. Only the access is limited: entry is allowed to members of the organisation after logging in.
Practical tasks: IP address, default gateway and network commands
The curriculum lists four practical tasks for this unit: identifying devices and cables (topics 1.2 and 1.4), checking the IP address and default gateway, using the commands ping, ipconfig, tracert and nslookup, and identifying RJ45 and fibre connectors (topic 1.3). The commands are described below.
(How are network commands run on a Windows computer?)
Command Prompt is opened on Windows (Windows key, type cmd, Enter) and the command is typed there. The outputs below are example outputs written for this post in the real Windows format; the addresses are sample values, and the numbers on another computer will be different. The addresses 192.0.2.x, 198.51.100.x and 203.0.113.x are reserved for examples, so they will not answer if typed; in the lab, the router's own address (shown by ipconfig) or an address given by the teacher is pinged instead.
ping
(What is the use of the ping command? How is its output read?)
ping sends a few small test packets (4 on Windows) to another device and waits for replies. It shows whether the device can be reached and how long a round trip takes.
C:\Users\Student> ping 192.0.2.10
Pinging 192.0.2.10 with 32 bytes of data:
Reply from 192.0.2.10: bytes=32 time=2ms TTL=128
Reply from 192.0.2.10: bytes=32 time=1ms TTL=128
Reply from 192.0.2.10: bytes=32 time=3ms TTL=128
Reply from 192.0.2.10: bytes=32 time=2ms TTL=128
Ping statistics for 192.0.2.10:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 1ms, Maximum = 3ms, Average = 2ms
Reading the output: 4 sent, 4 received, 0% loss means the device answered every test packet, so it can be reached. The average round trip is \( (2+1+3+2) \div 4 = 2 \) ms. TTL (time to live) is a counter that limits how many routers a packet may pass through before it is thrown away. Request timed out with 100% loss means the device did not answer: it may be off, the cable may be loose, or a firewall may be blocking ping.
ipconfig
(What is the use of the ipconfig command? How are the IP address and the default gateway of a computer found?)
Under each network adapter, ipconfig lists the device's own IP address, its subnet mask and the gateway (router) it uses to leave the network. The default gateway is the address of the router to which a computer sends data when the destination is outside its own network. ipconfig /all also shows the physical (MAC) address, which is the hardware address given to the network adapter by its maker (some devices can change it, for example for privacy on Wi-Fi), and the DNS servers, which are the computers that turn names into IP addresses.
C:\Users\Student> ipconfig
Windows IP Configuration
Wireless LAN adapter Wi-Fi:
Connection-specific DNS Suffix . :
Link-local IPv6 Address . . . . . : fe80::1a2b:3c4d:5e6f:7a8b%12
IPv4 Address. . . . . . . . . . . : 192.168.1.15
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.1.1
Reading the output: this computer is 192.168.1.15 (a private IPv4 address), and its router (default gateway) is 192.168.1.1. The subnet mask 255.255.255.0 tells the computer that addresses beginning 192.168.1. are on its own local network; data for any other address goes to the gateway. It also has a link-local IPv6 address starting with fe80, which works only between devices on the same local link (routers do not pass it on); the %12 at the end is the number Windows gives this adapter.
tracert
(What is the use of the tracert command?)
tracert (trace route) shows the routers (hops) on the path from the computer to a destination, with the round-trip time to each. Routers that do not answer its tests show as * * *, so the list can be incomplete. It helps to find where a connection becomes slow or stops.
C:\Users\Student> tracert example.com
Tracing route to example.com [203.0.113.80]
over a maximum of 30 hops:
1 2 ms 1 ms 2 ms 192.168.1.1
2 8 ms 7 ms 9 ms 198.51.100.1
3 15 ms 14 ms 16 ms 198.51.100.45
4 40 ms 39 ms 41 ms 203.0.113.80
Trace complete.
Reading the output: hop 1 is the computer's own router; in this example, hops 2 and 3 are routers of the ISP; hop 4 is the destination. Each hop is tested three times. A line of stars (* * *) means that router did not reply in time.
nslookup
(What is the use of the nslookup command?)
nslookup asks a DNS server which IP address belongs to a domain name (or which name belongs to an address).
C:\Users\Student> nslookup example.com
Server: router.home
Address: 192.168.1.1
Non-authoritative answer:
Name: example.com
Addresses: 2001:db8::80
203.0.113.80
Reading the output: the DNS server used was at 192.168.1.1, and the name example.com has one IPv6 and one IPv4 address. "Non-authoritative" only means the answer came from a DNS server that is not the domain's own (authoritative) server, for example one that looked it up on the computer's behalf or had saved (cached) it.
(State the use of ping, ipconfig, tracert and nslookup, with one situation for each.)
| Command | Main use | Situation in which it is used |
|---|---|---|
| ping | Tests if another device answers, and how fast | The lab printer or server is not responding |
| ipconfig | Displays the computer's IP address, the subnet mask and the default gateway | Setting up a lab computer or checking that it received an address |
| tracert | Shows the route (hops) to a destination | A website is slow and a rough idea of where the delay starts is needed |
| nslookup | Looks up the IP address that belongs to a domain name | A website name does not open but its address might |
Exam questions (CDC model paper 2083 pattern, with SEE 2081 and 2082 questions)
All questions below are practice questions written for this blog; none is copied from a paper or the textbook. They follow the patterns of the SEE 2081 and 2082 papers (old course) and the CDC model paper 2083 (the model for the new course, first examined in SEE 2083). The Pattern line shows which kind of SEE question each one practises. Mark splits are an estimate of how an examiner might divide the marks, following the CDC specification grid's rule of one mark for each key element expected in the answer. Where a topic above already answers a question, the answer is given by a link to that topic.
1-mark questions (Group A)
Q1. Which device connects a school's LAN to the ISP's network and chooses the route for each packet by reading IP addresses? (a) hub (b) repeater (c) switch (d) router
Pattern: Group A knowledge MCQ, reverse identification (name the item from its description, like the model paper's bandwidth MCQ). Marks: 1.
Answer: (d) router. See topic 1.4 Networking devices, question "Explain the functions of repeater, hub, switch, bridge and router."
Q2. Sunita wants to find the default gateway address of her laptop in Windows. Which command should she type? (a) ping (b) ipconfig (c) tracert (d) nslookup
Pattern: Group A application MCQ, "which command for this task" (the model paper had one command question). Marks: 1.
Answer: (b) ipconfig. See Practical tasks: ipconfig, question "What is the use of the ipconfig command?"
Q3. Two hostel buildings 450 m apart must be linked by cable. Why is optical fibre preferred over CAT6? (a) it carries electric current more strongly (b) it carries light with little loss over long distances and is not affected by electrical noise (c) it is the cheapest cable (d) it does not need any connector
Pattern: Group A understanding MCQ, "why is this medium suitable" (the model paper asked why one technology suits a situation). Marks: 1.
Answer: (b). (CAT6 is reliable only up to about 100 m.) See topic 1.2 Communication media, question "Worked example 4. A college wants to link two buildings 400 m apart. Which medium is suitable? Give reasons."
Q4. Which one of these is a correctly written IPv4 address? (a) 192.168.1.300 (b) 10.20.30 (c) 172.16.40.7 (d) 2001:db8::5
Pattern: Group A application MCQ: pick the one option that follows the IPv4 rules (each wrong option breaks one rule). Marks: 1.
Answer: (c) 172.16.40.7. (a) has 300, which is above 255; (b) has only three numbers; (d) is an IPv6 address. See topic 1.8 Concept of IP addressing, question "Worked example 7. State whether each address is valid: ..."
Q5. In a lab test, ping 203.0.113.80 (the web server's address in this question) gets four replies, but ping example.com shows "Ping request could not find host example.com". Which command should be used next to check whether the name can be turned into an IP address? (a) ipconfig (b) tracert (c) nslookup (d) ping again with the same name
Pattern: Group A application MCQ, choosing a command from two clues. Marks: 1.
Answer: (c) nslookup. The numeric address answers, so the path to that server is working at the moment; the problem lies in turning the name into an address (DNS name resolution), and nslookup checks exactly that.
Q6. The highest rate at which a communication channel is able to carry data is called its: (a) throughput (b) bandwidth (c) latency (d) frequency
Pattern: Group A knowledge MCQ, name the term from its description (model paper Q1). Marks: 1.
Answer: (b) bandwidth. See topic 1.1 Bandwidth and throughput, question "What is bandwidth?"
1-mark written practice (definitions and old-course style)
In the new course, Group A questions are multiple choice. The short written items below train the same facts and repeat the one-mark questions of the old-course SEE papers.
Q7. Why is Bluetooth, and not a CAT6 cable, used to join wireless earbuds to a phone?
Pattern: Group A understanding item, "why is this technology suitable" (model paper Q2). Marks: 1.
Answer: see topic 1.2 Unguided media, question "Why is Bluetooth suitable for connecting nearby devices?"
Q8. A network administrator wants to check from a lab computer whether the school server is answering. Which command is used?
Pattern: Group A application item, "which command for this task" (model paper Q3). Marks: 1.
Answer: ping. See Practical tasks: ping, question "What is the use of the ping command?"
Q9. Define telecommunication.
Pattern: one-sentence definition, asked in SEE 2081 Q1(a). Marks: 1.
Answer: see topic 1.1 Telecommunication, question "What is telecommunication?"
Q10. Write two examples of communication in simplex mode.
Pattern: very short item, asked in SEE 2081 Q1(b). Marks: 1.
Answer: see topic 1.1 Modes of communication, question "Explain simplex, half duplex and full duplex mode with examples." (FM radio broadcast and TV broadcast.)
Q11. What is meant by transmission media?
Pattern: very short item, asked in SEE 2082 Q1(a). Marks: 1.
Answer: see topic 1.2 Communication media, question "What is transmission media?"
Q12. Write the full forms of (a) LAN and (b) RFID.
Pattern: full-form item, asked in SEE 2082 Q3(a) (LAN). Marks: ½ + ½.
Answer: (a) Local Area Network; (b) Radio Frequency Identification. Other full forms of the unit are listed in the full forms table.
2-mark questions (Group B)
Q13. Bandwidth and throughput are both measured in bits per second, yet they are not the same thing. Give two points that set them apart.
Pattern: Group B "differentiate two terms" (the model paper's Q11 style), on the term the model MCQ tested. Marks: 1 + 1.
Answer: see topic 1.1 Bandwidth and throughput, question "Differentiate between bandwidth and throughput." (One mark for each row.)
Q14. Ramesh listens to music on wireless earbuds while his phone stays in his pocket. (a) Name the wireless technology used and the type of network formed by area. (b) Explain briefly how the technology works.
Pattern: Group B application, "identify the technology in a daily-life situation and explain how it works" (the model paper's Q12 style). Marks: (a) ½ + ½, (b) 1.
Answer: (a) Bluetooth (½); it forms a PAN, a Personal Area Network (½). (b) After the phone and earbuds are paired, the phone sends the music to them as short-range, low-power radio signals, and the earbuds receive and play it (1).
Further detail (not needed for the mark): Bluetooth uses the 2.4 GHz band, typically works over about 10 m, and keeps hopping between channels to avoid interference.
Q15. A student wrote: "A hub is better than a switch because a hub sends each packet only to the computer it is meant for." Find the mistake and write the correct statement.
Pattern: Group B error-correction item, built on the classic hub/switch difference (a likely "differentiate" pair, not yet asked in the papers reviewed). Marks: 1 (mistake found) + 1 (correct statement).
Answer: The student has swapped the two devices: a hub does not send data only to the destination; it copies every packet out of all its other ports (1). Correct statement: "A switch, not a hub, sends each packet only to the port of the destination computer, using the table of MAC addresses it has learned; a hub sends the packet to every other computer, wasting bandwidth." (1)
Q16. A shop has a 50 Mbps Internet plan. A 300 MB file takes 80 seconds to download (take 1 MB = 8 Mb, in decimal units). (a) Calculate the throughput. (b) Give one reason why it is lower than the bandwidth.
Pattern: Group B application, short data task with units (allowed by the grid's application level; not yet seen as a numerical in a real paper). Marks: 1 + 1.
Given: bandwidth = 50 Mbps; file size = 300 MB; time = 80 s; 1 MB = 8 Mb.
To find: (a) throughput; (b) one reason it is lower than the bandwidth.
Formula: throughput = data transferred (bits) ÷ time taken.
Solution: (a) Data in megabits = \( 300 \times 8 = 2400 \) Mb. Throughput \( = \dfrac{2400\ \text{Mb}}{80\ \text{s}} = 30\ \text{Mbps} \) (that is 60% of the 50 Mbps bandwidth). This is the average throughput over the whole download.
Answer: (a) 30 Mbps. (b) Many users share the line at the same time (congestion); other accepted reasons: weak Wi-Fi signal or interference, a busy server, or a slow device.
Q17. Name the mode of communication used in each case: (i) an FM radio station broadcasting a song (ii) two security guards using walkie-talkies (iii) a video call between two friends (iv) a TV station broadcasting a cricket match to homes.
Pattern: Group B reverse identification; the old SEE 2081 paper asked for examples of simplex mode, here turned around. Marks: ½ each.
Answer: (i) simplex (ii) half duplex (iii) full duplex (iv) simplex.
Q18. Differentiate between an intranet and an extranet on (i) who can use it and (ii) its main purpose.
Pattern: Group B "differentiate two terms" on two given points. Marks: 1 + 1 (one for each row, with both sides written).
| Intranet | Extranet |
|---|---|
| (i) Only the organisation's own members, such as its staff (and students, in a school), can use it. | (i) Members and also chosen outsiders, such as suppliers, partners or parents, who have been given permission. |
| (ii) Helps people inside the organisation share notices, files and tools with one another. | (ii) Lets the organisation share selected information or services, such as orders or results, with those outsiders. |
Q19. A student runs two commands on a lab computer and sees the lines below. (a) Write the computer's IP address and the address of its router. (b) What does the ping result tell the student?
C:\Users\Student> ipconfig
...
IPv4 Address. . . . . . . . . . . : 192.168.10.23
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.10.1
C:\Users\Student> ping 192.168.10.1
...
Ping statistics for 192.168.10.1:
Packets: Sent = 4, Received = 0, Lost = 4 (100% loss),
Pattern: Group B application, reading command output from the practical. Marks: (a) ½ + ½, (b) 1.
Answer: (a) IP address: 192.168.10.23 (½). Router (default gateway): 192.168.10.1 (½). (b) No reply came back for any of the four test packets: either the computer cannot reach its router at the moment, or the router (or a firewall) is set to ignore ping (1). Sensible next checks: the cable or Wi-Fi connection, whether the router is switched on, and whether a firewall is blocking ping.
Q20. At a library counter, a book is recorded the moment it is laid on a flat pad, although nobody scans a barcode. (a) Name the technology. (b) Explain the jobs of the tag and the reader.
Pattern: Group B application, "name the technology in this situation and explain how it works" (like Q14). Marks: (a) 1, (b) ½ (tag) + ½ (reader).
Answer: (a) RFID (Radio Frequency Identification) (1). (b) A small tag fixed inside the book stores the book's identification number (½). The reader in the pad sends out radio waves; the tag answers with its number without any touching, and the reader passes the number to the library software (½).
Further detail: library tags are usually passive (no battery, read only close to the reader); active tags carry a battery and can be read from farther away.
Q21. A hospital in Pokhara uses 4G in its ambulances and plans to move to 5G. Give two ways in which 5G would help.
Pattern: Group B understanding, comparing mobile generations in a real situation. Marks: 1 + 1 (any two points).
Answer: Any two: (1) Much higher speed, so large files such as scan images, or live HD video from the ambulance, reach the doctors quickly. (2) Much lower delay (latency), so live video and instructions between the ambulance crew and the doctors pass with much less lag (where the 5G coverage is good). (3) Far more devices can stay connected in the same area, so monitors and sensors in every ambulance and ward can stay online together.
Q22. What is a data packet? Give one reason why a network sends a file as many packets instead of one large block.
Pattern: Group B knowledge and understanding, define a term and give a reason. Marks: 1 + 1.
Answer: see topic 1.1 Data packets, question "What is a data packet?" (1), and question "Why is a message sent as many data packets instead of one block?" (any one reason, 1).
Q23. Write two points of difference between guided media and unguided media.
Pattern: Group B "differentiate", asked in SEE 2081 Q4(a). Marks: 1 + 1.
Answer: see topic 1.2 Guided and unguided media compared, question "Differentiate between guided and unguided media." (Two rows, with both sides written.)
Q24. Give two ways in which a client-server network differs from a peer-to-peer network.
Pattern: Group B "differentiate", asked in SEE 2082 Q4(a). Marks: 1 + 1.
Answer: see topic 1.7 Network architecture, question "Differentiate client-server architecture from peer-to-peer architecture." (Any two rows.)
Q25. Write two differences between the internet and an intranet.
Pattern: Group B "differentiate two terms" (model paper Q11). Marks: 1 + 1.
Answer: see topic 1.9 Concept of the internet, intranet and extranet, question "Differentiate between internet and intranet." (Any two rows.)
Q26. Bina's laptop at home reaches the Internet although no cable is plugged into it. Name the technology and state how it works.
Pattern: Group B application, "name the technology and explain how it works" (model paper Q12). Marks: 1 (Wi-Fi) + 1 (how it works).
Answer: see topic 1.2 Unguided media, question "How does a laptop connect to the Internet through Wi-Fi?"
Q27. Write one advantage and one disadvantage of star topology.
Pattern: Group B understanding item on topology. Marks: 1 + 1.
Answer: see topic 1.5 Topology, question "Write the advantages and disadvantages of bus, star, ring and hybrid topology." (Star row.)
4-mark questions (Group C)
Q28. A community school in a hill village has no telephone line, and the nearest fibre network ends 15 km away. A mobile tower near the school gives a strong 4G signal. (a) State briefly what makes an Internet connection "broadband". (b) Explain any two types of broadband connection, with one feature of each. (c) Which type should be recommended for this school now? Give one reason.
Pattern: Group C, types of broadband with features (the model paper's long question topic), set in a new scenario. Marks: (a) 1 + (b) 1 + 1 + (c) 1.
Answer:
(a) Broadband is fast Internet that stays connected all the time and can carry a lot of data, such as video, voice and files, together.
(b) Any two (1 mark each: the type with one correct feature). Model answer:
- Fibre optic: carries data as light through glass fibres; it is very fast and reliable over long distances, but the cable must be laid up to the building.
- Wireless (4G/5G mobile broadband): uses radio waves from a nearby tower; no cable is needed and it can be set up quickly with a router or SIM, but the speed depends on signal strength and the number of users.
Other types also accepted in (b): satellite (uses a dish to communicate with a satellite; works even in very remote places, but is costly and has a noticeable delay) and DSL (uses the telephone line; reuses existing lines, but gets slower farther from the exchange).
(c) Wireless (4G) broadband, because the tower already gives a strong signal and no cable needs to be laid. DSL is impossible without a phone line, and fibre would take time and money to bring 15 km. (Satellite may also earn the mark if a sound reason is given, such as that it needs no ground cable; but 4G is the better choice here, because satellite costs more and has a noticeable delay.)
Q29. (a) Contrast the client-server and peer-to-peer architectures on any two points. (b) A school with 80 computers wants every student to log in with their own account and to save work in one place that is backed up every day. Which architecture should it choose? Give two reasons.
Pattern: Group C [2+2]; the old SEE 2082 paper asked for two differences between these architectures as a short question; here the comparison is reworded and extended with a choose-and-justify part. Marks: (a) 1 + 1, (b) 1 (choice with first reason) + 1 (second reason).
Answer:
(a)
| Client-server | Peer-to-peer |
|---|---|
| Has a dedicated central server that provides services to client computers. | Has no dedicated server; every computer is equal and both shares and uses resources. |
| Control, security and backup are central, managed by an administrator. | Each user controls their own computer; backup and security are done one by one. |
(b) Client-server. Reasons: (1) the server can store every student's account and check each login from one place, which is not practical on 80 separate peers; (2) all work is saved on the server, so one daily backup protects everyone's files. (Also accepted: better security and easier management of a large network.)
Q30. The digital room of a college library has 12 computers, one printer, one switch and one router connected to the Internet. (a) Draw a labelled diagram of this room's network in star topology. (b) Explain how a print job from PC3 reaches the printer, and state what happens if the cable of PC5 breaks and if the switch fails.
Pattern: Group C two-part long question with a [2+2] split (the model paper uses [2+2] for Q23 and Q24); a design-and-explain item on topology and devices, a likely new-course type (not yet seen in a board paper). Marks: (a) 2 (correct star layout + labels), (b) 1 (path) + ½ (PC5 cable breaks) + ½ (switch fails).
Answer:
(a)
Figure 12: Model answer diagram for Q30: a library room network in star topology.
(b) PC3 breaks the print job into packets and sends them through its own cable to the switch. The switch reads the destination MAC address (the printer's) and forwards the packets only to the printer's port; the printer joins them and prints. If PC5's cable breaks, only PC5 is cut off and all other computers keep working. If the switch fails, no device can communicate with another or reach the router, so the whole room's network stops.
Q31. A ward office in a town wants to choose an Internet connection. (a) What is broadband? (b) Describe three types of broadband connection, giving one feature and one suitable use of each.
Pattern: Group C, types of broadband with features and uses, adapted from the model paper's long question (whose answer key gives 1 mark for an introduction and 3 for the types, features and uses), with a [1+3] split. Marks: (a) 1, (b) 1 for each type (½ for a correct feature + ½ for a suitable use).
Answer:
(a) Broadband is Internet access with a high data rate that stays on all the time, so video, voice and files can travel together (1).
(b) Any three, for example:
| Type | One feature | One suitable use |
|---|---|---|
| DSL | Uses the existing copper telephone line; it gets slower farther from the telephone exchange. | A home or small office close to the exchange. |
| Fibre optic | Carries data as light through glass; very fast and not disturbed by electrical noise. | Offices, banks and schools that need high, steady speed. |
| Satellite | Works almost anywhere through a dish, but costs more and has a noticeable delay. | A remote village with no cable or mobile tower. |
Also accepted: cable broadband (uses the coaxial cable of cable TV; speed drops when many neighbours are online; suits towns with cable TV) and wireless broadband (4G/5G or fixed wireless; no cable to each user; suits places with good mobile coverage). The full comparison of the five types is in topic 1.1 Broadband, question "What is broadband? What are the types of broadband connection?"
Q32. Networks are grouped by the area they cover. Explain PAN, LAN, MAN and WAN, giving one example of each.
Pattern: Group C "types with features and examples" [4]; LAN was asked as a full form in SEE 2082. Marks: 1 for each type (area + example).
Answer: see topic 1.6 Overview of different networks based on coverage, question "Explain PAN, LAN, MAN and WAN with an example of each."
Q33. Describe the function of any four networking devices.
Pattern: Group C "types with features" [4]. Marks: 1 for each device with its function correctly described (a place where it is used may be added as support).
Answer: see topic 1.4 Networking devices, question "Explain the functions of repeater, hub, switch, bridge and router." (Any four rows.)
Q34. State the purpose of the commands ping, ipconfig, tracert and nslookup, with one situation in which each is useful.
Pattern: Group C practical-based item [4]; the model paper tested one command as an MCQ. Marks: 1 for each command.
Answer: see Practical tasks, question "State the use of ping, ipconfig, tracert and nslookup, with one situation for each."
Q35. Explain bus, star and ring topology. Write one advantage and one disadvantage of star topology.
Pattern: Group C "types with features" [3+1]. Marks: 1 for each topology explained, ½ for one advantage and ½ for one disadvantage of star topology.
Answer: see topic 1.5 Topology, question "Explain bus, star, ring and hybrid topology." (bus, star and ring), and question "Write the advantages and disadvantages of bus, star, ring and hybrid topology." (Star row.)
Quick revision
| Topic | Key point |
|---|---|
| Telecommunication | Communication over distance with electronic signals; parts: sender, receiver, message, medium, protocol. |
| Broadband types | DSL (phone line), cable (TV coaxial), fibre (light), satellite (dish), wireless (4G/5G, Wi-Fi). |
| Bandwidth vs throughput | Capacity vs actual rate; both in bps; time = file size in bits / throughput. |
| 3G / 4G / 5G | Mobile Internet / fast HD video, low latency (LTE) / very fast, very low delay, many IoT devices. |
| Packet | Header (from, to, number) + data; can take different routes; lost data re-sent (TCP), not the whole file. |
| Frequency | Waves per second in Hz; Wi-Fi 2.4 and 5 GHz; Bluetooth 2.4 GHz; FM 88 to 108 MHz. |
| Modes | Simplex (one way: radio), half duplex (turns: walkie-talkie), full duplex (both together: phone call). |
| Guided media | CAT6 twisted pair (1 Gbps up to 100 m, RJ45), coaxial, optical fibre (light, km, no electrical noise). |
| Unguided media | Wi-Fi, Bluetooth (about 10 m, PAN), RFID (tags and readers; passive/active), satellite (uplink/downlink). |
| Connectors | RJ45 (8 pins, Ethernet), fibre SC/LC/ST, media converter (electric to light and back). |
| Devices | Repeater regenerates (boosts) signals; hub copies to all other ports; switch sends to the destination port (MAC); bridge joins segments; router joins networks (IP, best path). |
| Topologies | Bus (backbone, terminators), star (central switch), ring (loop, one way), hybrid (mix). |
| By area | PAN (about 10 m), LAN (building/campus), MAN (city), WAN (country/world; the Internet). |
| Architecture | Client-server (central server, security, backup) vs peer-to-peer (equal computers, cheap, small). |
| Protocols | TCP/IP, HTTP, HTTPS, DHCP, SMTP, FTP, DNS; NCP was the first (ARPANET). |
| IP addresses | IPv4: 32 bits, 4 dotted decimals 0 to 255, about 4.3 billion. IPv6: 128 bits, 8 hex groups with colons, about \( 3.4 \times 10^{38} \). |
| Internet / intranet / extranet | Public for everyone / members only / members plus invited outsiders. |
| Commands | ping (reachable?), ipconfig (own IP and gateway), tracert (route and hops), nslookup (name to IP). |
Full forms
| Short form | Full form | Short form | Full form |
|---|---|---|---|
| LAN | Local Area Network | DSL | Digital Subscriber Line |
| MAN | Metropolitan Area Network | bps | bits per second |
| WAN | Wide Area Network | ISP | Internet Service Provider |
| PAN | Personal Area Network | RFID | Radio Frequency Identification |
| WLAN | Wireless Local Area Network | CAT6 | Category 6 (cable) |
| IP | Internet Protocol | RJ45 | Registered Jack 45 |
| IPv4 / IPv6 | Internet Protocol version 4 / version 6 | Wi-Fi | Wireless Fidelity (textbook form; officially a brand name) |
| TCP/IP | Transmission Control Protocol / Internet Protocol | LTE | Long Term Evolution |
| DNS | Domain Name System | NAT | Network Address Translation |
| NCP | Network Control Protocol | MAC | Media Access Control (address) |
| HTTP | HyperText Transfer Protocol | HTTPS | HyperText Transfer Protocol Secure |
| DHCP | Dynamic Host Configuration Protocol | SMTP | Simple Mail Transfer Protocol |
| FTP | File Transfer Protocol | FTTH | Fibre To The Home |
| NIC | Network Interface Card | IRC | Internet Relay Chat |
| IoT | Internet of Things | AR / VR | Augmented Reality / Virtual Reality |
Next unit: Unit 2 - Database Management System: Notes and Exam Questions.
Leave a Comment